Spit Rod Hanger Tapcon
Rod Hanger Tapcon Vertical for Concrete the overhead threaded rod anchoring system
Applications
Fire protection - sprinkler systems, plumbing / Mechanical Contractors - air, water, hydraulics,
Electrical Contractors - conduit, cable trays, lighting, low voltage cabling, HVAC - unit heaters,
A/C units, duct work, refrigeration, industrial maintenance - work in the rafters
RHT installation with IWI
Basket Tray Installation
|
Product Features
| Installs in less than half the time of drop-in anchors |
| Single piece design, no nut and washer to assemble |
| Suitable for concrete, steel and wood based materials |
| Concrete installation requires smaller diameter drill bits than traditional drop-in anchors |
| All metal fixings offer fire resistance |
| Easily removable / replaceable |
| Close to edge fixing giving high performance values |
| Can be fixed closer together than traditional anchors without reducing performance values |
| Self tapping in concrete and cuts its own thread in wood and steel |
| Low cost Condrive kits allow fast installation |
| Allows vertical and horizontal installation in hard to reach locations |
| Premium corrosion protection |
| Shallow embedment gives flexibility in steel, concrete and wood |
Steel version employs proven Teks technology
RHT Features & Benefits Tour |
Specification
| Diameter | 8mm |
| Threaded rod | M10 |
| Thread form | Reverse Hi-Lo |
| Point type | Nail |
| Finish | Blue Climaseal |
| Head style | Female M10 |
| Kesternich Results (DIN 5008, 2.0L) | 30 Cycles - 10% or less red rust Salt Spray Results
(ASTM B117) = 750 Hours - 10% or less red rust |
Installation
| When installing the self tapping screw into concrete, use up to 1,200 RPM drill (maximum) |
| Use either a standard 6.5mm SDS / masonry drill bit or a Hex receiver drill bit for use with the concrete Condrive kit code 921433 |
| Drill a hole in the base material to a depth of 54mm with an electric impact/drill set on impact mode |
| If using the Condrive system install the sleeve over the drill bit (the drill bit should remain in the tool) |
| Insert the appropriate nut driver in the sleeve (Black Nut driver code 921406) |
| Insert the concrete screw into the nut driver |
| Place the tip of the screw into the pre-drilled hole, ensuring it is switched to drill mode and begin insertion |
| When the nut driver spins free on the screw, installation is complete |
| Stop and remove the drill and screw threaded rod into the female threaded socket |
| Note: Do not install the concrete screws while the drill is in impact mode - doing so will destroy the pull-out factor of the screw. When fixing into pre-cast hollow concrete beams ensure Rod Hanger Tapcon is fixed into the web for best pull-out result |
| The installation sockets are designed with a unique
automatic release mechanism to prevent over tightening. This provides a fast
and safe installation each time. When the face of the driver comes in
contact with the material you are installing into, continue drilling until
nut driver spins free. Installation is then complete |
Substrates
| Wood - joist, flooring, composite joist / truss, steel, concrete, pre-cast concrete beams, block work, brickwork
|
Product Range
| Code | Anchor Ø | Hole Ø | Length | Drilling Depth | Box Qty |
|---|
| 921649 | 8mm | 6.5mm | 44mm | 54mm | 25 |
| 921413 | 8mm | 6.5mm | 44mm | 54mm | 25 |
Cut Box Range
| Code | Anchor Ø | Hole Ø | Max Fixture | Length | Box Qty |
|---|
| 921542 | 8mm | 6.5mm | 44mm | 54mm | 20x4 |
Accessories
| Code | Description | Box Qty |
|---|
| 921439 | Concrete Condrive Kit | 1 |
Approvals
| NFPA National Fire Protection Association |
