Spit Hex Head & Countersunk Tapcon

Drill, Drive, Done

The original masonry fastening system that cuts it's own thread into concrete, brick and hollow block

Applications

Plastic trunking installed with Countersunk Tapcon

Plastic back box installed with Countersunk Tapcon

Electrical Accessories

Saddles, conduit clips, back boxes, P Clips, cable clips, cable Cleats

Services

Ductwork, cable trays, channel, suspended ceilings, timber to concrete, formwork, battens, base plates, plywood backer boards insulation systems to masonry

Metalwork

Railings, hand rails, gates, brackets and signs, fire protection and exterior

Product Features

Fast installation, Drill, Drive, Done

Available in M5 and M6 and in lengths from 32 - 125mm, to cover a wide number of applications

Every box includes a free 'close tolerance' masonry bit

Replaces small diameter expansion anchors, plugs and screws in light to medium duty applications

No need to pre-spot holes, no inserts are required

Removable - adjustable

Can be installed close to edges

Slotted Hex and Phillips flat head styles give flexibility in applications

Excellent corrosion protection

Fire resistant

Specification

Diameter	5mm-6mm
Thread form	Reversed Hi-Lo
Point type	Nail
Finish	Blue Climaseal
Kesternich results	(DIN 5008, 2.0L) 30 Cycles-10% or less red rust
Corrosion	Salt spray (ASTM B117) = 750 hours - 10% or less rust

Head Styles

Phillips Flat Head	5mm Diameter: P2 Phillips Flat Head
Phillips Flat Head	6mm Diameter: P3 Phillips Flat Head
Slotted Hex Washered Head	5mm Diameter: 6.5mm Slotted Hex Washered Head
Slotted Hex Washered Head	6mm Diameter: 8mm Slotted Hex Washered Head

Installation

With Condrive Sleeve off and drill bit exposed, drill pilot hole deeper than recommended anchor embedment. Snap correct anchor socket / drive bit onto end of Condrive Sleeve. Slide Condrive Sleeve over drill bit

Insert head of Tapcon anchor into Hex or Phillips socket

Put point of anchor into pre-drilled hole and drive until anchor is fully seated

Ensure that the drilling tool is not set to hammer action during installation

Substrates

Concrete, masonry, block work, pre-cast hollow concrete beams, wood, concrete, non cracked concrete

Product Range

Countersunk Tapcon Range

Code	Thread Ø	Drill Ø	Fixture	Length	Box Qty
921507	5mm	4mm	0-7mm	32mm	100
921508	5mm	4mm	5-20mm	45mm	100
921509	5mm	4mm	17-32mm	57mm	100
921510	5mm	4mm	30-45mm	70mm	100
921511	5mm	4mm	42-57mm	82mm	100
921512	5mm	4mm	60-75mm	100mm	100
921513	6mm	5mm	0-7mm	32mm	100
921514	6mm	5mm	5-20mm	45mm	100
921515	6mm	5mm	17-32mm	57mm	100
921516	6mm	5mm	30-45mm	70mm	100
921517	6mm	5mm	42-57mm	82mm	100
921518	6mm	5mm	60-75mm	100mm	100
921519	6mm	5mm	85-100mm	125mm	100

Countersunk Tapcon Cut Box Range

Code	Thread Ø	Drill Ø	Fixture	Length	Box Qty
567034	5mm	4mm	17-32mm	57mm	10x15
567035	5mm	4mm	30-45mm	70mm	10x15
567036	6mm	5mm	42-57mm	82mm	10x10
567037	6mm	5mm	60-75mm	100mm	10x10

Hex Head Tapcon

Code	Thread Ø	Drill Ø	Fixture	Length	Box Qty
921498	5mm	4mm	0-7mm	32mm	100
921499	5mm	4mm	5-20mm	45mm	100
921500	5mm	4mm	17-32mm	57mm	100
921501	6mm	5mm	0-7mm	32mm	100
921502	6mm	5mm	5-20mm	45mm	100
921503	6mm	5mm	17-32mm	57mm	100
921504	6mm	5mm	30-45mm	70mm	100
921505	6mm	5mm	42-57mm	82mm	100
921506	6mm	5mm	60-75mm	100mm	100

NB. Supplied with one D end rotary percussion masonry bit in every box

Hex Head Cut Box Range

Code	Thread Ø	Drill Ø	Fixture	Length	Box Qty
921526	5mm	4mm	0-7mm	32mm	20x25
921527	6mm	5mm	0-7mm	32mm	20x25
921528	6mm	5mm	5-20mm	45mm	20x25
921529	6mm	5mm	42-57mm	82mm	15x25

Accessories

Countersunk Tapcon Accessories

Code	Description	Box Qty
921159	Tapcon Condrive Kit 1000	1
921557	6.5mm Drive Tru Socket 5mm Diameter Hex Head Tapcon	1
921469	8mm Drive Tru Socket for 6mm Diameter Hex Head Tapcon	1

Hex Head Tapcon Accessories

Code	Description	Box Qty
921159	Tapcon Condrive Kit 1000	1
P2	Phillips Nº 2 Driver Bit	1
P3	Phillips Nº 3 Driver Bit	1

Countersunk & Hex Head Tapcon Drill Bits

Code	Description	Box Qty
921126	SDS 4x110 Tapcon Drill Bit	1
921127	SDS 4x140 Tapcon Drill Bit	1
921138	SDS 5x110 Tapcon Drill Bit	1
921139	SDS 5x140 Tapcon Drill Bit	1
921140	SDS 5x165 Tapcon Drill Bit	1

Drill Bits for use with Condrive Sleeve

Code	Description	Box Qty
921137	SDS 4x180 Tapcon Drill Bit	1
921154	SDS 5x180 Tapcon Drill Bit	1

Approvals

SBCCi Approved 9759

Metro-Dade Approved 02 - 0311 - 03

ICBO Approved 3370

Downloads

Where now?

Find your nearest distributor

Need help selecting the right fixing

Join the club